FREE DELIVERY TODAY - Place your 1st order.
Simrad RF300 Rudder Feedback
Measuring rudder angle geometry without potentiometer dead zones, a Simrad RF300 marine autopilot sensor transmits 2-wire variable frequency signals across a +/- 90-degree range to NAC-2, NAC-3, and AC70 processors at 12V.
- Variable frequency sensing measures 90-degree rudder angles
- Non-contact sensor architecture prevents mechanical wear
- IP56-rated polymer housing protects internal circuitry
- Includes 10-meter cable for long-run bilges
Products are almost sold out
available only:
7In Stock
Description
Provide accurate rudder-angle data to a compatible Simrad autopilot with the Simrad RF300 Rudder Feedback Unit. This mechanical feedback sensor connects to the rudder post or tiller arm through its supplied transmission linkage and 10 m cable, helping the autopilot determine the actual rudder angle for smoother and more accurate automatic steering. The RF300 is designed for inboard-engine vessels and is commonly included with commercial Simrad autopilot systems. [256][257]
The RF300 uses a two-wire frequency-feedback connection and is intended for NAC-3 or AC70-class autopilot-computer installations; Simrad specifically identifies it as a two-wire feedback unit for NAC-3 systems where running NMEA 2000 to the rudder area is impractical. It is a sensing device only, not a steering drive, pump, or standalone autopilot. [253][254]
Key Specifications
- Mechanical rudder-position feedback sensor for compatible Simrad autopilot installations.
- Measures rudder angle through a mechanical transmission linkage connected to the rudder post or tiller arm.
- Uses a two-wire frequency-feedback interface for compatible course computers.
- Designed for NAC-3 and AC70-class systems; verify exact computer compatibility before installation.
- Includes a 10 m, or 33 ft, cable and transmission linkage.
- Supports approximately plus or minus 90 degrees of rudder-angle movement when installed with correct linkage geometry.
- Uses a compact corrosion-resistant housing rated IP56 with a stated operating range of minus 25°C to 55°C.
- Weighs approximately 0.5 kg including the cable.
Installation Considerations
Mount the RF300 so its movement accurately follows rudder movement throughout the full steering range. The transmission link must be aligned correctly, free from binding, protected from damage, and positioned so neither the sensor nor linkage reaches its mechanical limit before the rudder reaches full travel.
Use this sensor where physical rudder feedback is required. It does not replace a steering drive, hydraulic pump, course computer, heading sensor, display, or NMEA 2000 network. Follow the applicable Simrad installation manual for linkage geometry, wiring, rudder-centering, dockside calibration, and sea-trial setup.
Before Ordering
Confirm the existing autopilot computer is compatible with the RF300 frequency-feedback interface, verify access to the rudder post or tiller arm, measure cable-routing distance against the supplied 10 m cable, check full rudder-travel geometry, and ensure a protected IP56-appropriate mounting location before purchase.
Simrad RF300 Rudder Feedback
| Drive Type | Rudder Position Feedback Sensor |
|---|---|
| Pump/Ram Capacity | N/A (Sensing Unit) |
| Flow Rate / Speed | High-Precision Position Tracking |
| Max Pressure | N/A (Mechanical Linkage) |
| Cylinder Compatibility | Universal Hydraulic/Mechanical Rudders |
| Operating Voltage | 12V DC (via Pilot Computer) |
| Peak Current Draw | Low-Draw Analog Signal |
| Average Power Draw | Minimal Sensor Power |
| Motor Type | Variable Frequency Transmitter |
| Computer Compatibility | NAC-2, NAC-3, AC12, AC42, AC70 |
| Port Size / Thread | N/A (Mechanical Joint) |
| Drive Connection | 2-Wire Frequency Interface |
| Rotation/Stroke Direction | +/- 90 Degree Operating Range |
| Mounting Type | Rudder Post / Tiller Arm Link |
| Housing Material | Corrosion-Resistant Polymer |
| Waterproof Rating | IP56 High-Level Protection |
| Operating Temperature | -25°C to +55°C Marine Grade |
| Length (Overall) | Variable Linkage Arm Length |
| Width/Diameter | Compact Sensor Housing |
| Weight | 0.5 kg (Including Cable) |
| Included Accessories | 10m Cable, Transmission Linkage |
| Key Mechanical Feature | Non-contact high-resolution sensing |
You must be logged in to post a review.













Reviews
There are no reviews yet.