FREE DELIVERY TODAY - Place your 1st order.
Simrad RF45X Rugged Rudder Feedback Unit w/Tansmission Link, 2M Cable & Junction Box
Large commercial yachts track rudder geometry through severe bilge washdowns using this Simrad RF45X marine autopilot, which transmits a +/- 45-degree sweep via double-bearing die-cast metal construction across 12V or 24V processors at 1.8 kg.
- Double-bearing design ensures commercial mechanical durability
- IP67 submersible housing prevents bilge flooding
- Transmits precise 45-degree rudder angle sweep
- Operates reliably from -25°C to 70°C
Products are almost sold out
available only:
7In Stock
Description
The Simrad RF45X Rugged Rudder Feedback Unit is a medium-duty physical rudder-angle sensor for compatible Simrad autopilot and rudder-angle-indicator installations. It mounts close to the rudder stock and connects mechanically to the tiller arm through a transmission link at a 1:1 ratio. The RF45X sends rudder-angle information to the autopilot computer and can also provide a separate signal for a standalone rudder-angle indicator. [297][300]
This kit includes the transmission linkage, a 2 m cable, and a junction box. The RF45X is mechanically similar to the older RF45 but is repairable rather than a sealed disposable unit. Its variable-frequency, pulse-width-modulated output is selectable for compatible Simrad and Robertson autopilot computers, including legacy ACXX, J3XX, J50, AP45, and AP9 Mk3 architectures; confirm the exact input compatibility before purchase. [297][298]
Key Specifications
- Medium-duty physical rudder-feedback unit for compatible Simrad commercial and larger-vessel autopilot installations.
- Mounts near the rudder stock and connects to the tiller arm through a 1:1 mechanical transmission linkage.
- Supplies a variable-frequency pulse-width-modulated rudder-angle signal to a compatible autopilot computer.
- Can provide a second variable-current signal for a compatible standalone rudder-angle indicator.
- Includes a transmission link, 2 m cable, and junction box.
- Features a repairable design mechanically based on the earlier Simrad RF45 feedback unit.
- Supports compatible 12V or 24V installations, with 24V use applicable to supported standalone rudder-angle-indicator arrangements.
- Uses a ruggedized, corrosion-resistant housing with a stated IP67 rating and an operating range of minus 25°C to 70°C.
Installation Considerations
Mount the feedback unit on a rigid, flat surface close to the rudder stock. Centre the vessel rudder before connecting and adjusting the transmission linkage, then ensure the linkage moves freely without binding, collision, side load, or reaching the sensor’s mechanical limit before full rudder travel.
The supplied 2 m cable and junction box provide a local connection point, but cable routing to the autopilot computer must be planned separately. Keep signal wiring protected from moving steering components, heat, moisture ingress, and high-current cables. Complete the autopilot’s rudder-feedback calibration and verify accurate port, starboard, and amidships readings before sea trial.
Before Ordering
Confirm the autopilot computer accepts the RF45X output type, verify the required jumper configuration, check access to the rudder stock and tiller arm, confirm 1:1 transmission-link geometry, allow for the 2 m supplied cable and junction-box location, provide a protected IP67-appropriate mounting area, and verify the required 12V or 24V system configuration before purchase.
Simrad RF45X Rugged Rudder Feedback Unit w/Tansmission Link, 2M Cable & Junction Box
| Drive Type | Heavy-Duty Rudder Feedback Unit |
|---|---|
| Pump/Ram Capacity | N/A (Sensing Unit) |
| Flow Rate / Speed | High-Resolution Position Output |
| Max Pressure | Mechanical Transmission Linkage |
| Cylinder Compatibility | Commercial & Large Yacht Rudders |
| Operating Voltage | 12V / 24V DC Support |
| Peak Current Draw | Industrial Signal Level |
| Average Power Draw | Low-Power Solid State Sensing |
| Motor Type | Frequency Modulated (Long Run) |
| Computer Compatibility | AC70, AC80, NAC-3, J300X |
| Port Size / Thread | Stainless Steel Linkage Rod |
| Drive Connection | Junction Box Multi-Wire Link |
| Rotation/Stroke Direction | +/- 45 Degree Precise Sweep |
| Mounting Type | Deck/Bulkhead Rugged Mount |
| Housing Material | Corrosion-Resistant Die-Cast Metal |
| Waterproof Rating | IP67 Submersible Grade |
| Operating Temperature | -25°C to +70°C Extreme Grade |
| Length (Overall) | Variable Transmission Link Rod |
| Width/Diameter | Heavy-Duty Industrial Chassis |
| Weight | 1.8 kg (Full Kit w/ Junction Box) |
| Included Accessories | Linkage, 2M Cable, Junction Box |
| Key Mechanical Feature | Double bearing design for commercial use |
You must be logged in to post a review.













Reviews
There are no reviews yet.