Aquaglide Catapult Trapeze Commercial Water Swing

Description

Configured as a free-swing overhang and climbing tower, theAquaglide Catapult Trapezeuses Duratex 1100-denier PVC with overlapping hot-air welded seams. The 13 ft 5 in by 11 ft 2 in footprint supports up to three concurrent users within a stated 600 lbs total payload. Three independent float chambers operate at 1.2 PSI.

Fourteen molded handles and textured step treads provide the listed climbing layout. Four marine-grade 316 stainless steel D-rings form the mooring points. the listed 8 ft minimum water depth defines the listed launch-drop clearance zone.

Key Features of the Catapult Trapeze

• Duratex 1100-denier PVC forms the listed free-swing overhang and climbing-tower construction.
• Overlapping hot-air welded seams provide the listed structural seam technology.
• Three users can occupy the module within the listed 600 lbs total payload.
• An 8 ft minimum water depth provides the listed launch-drop clearance zone.
• Three independent float chambers operate at the listed 1.2 PSI pressure.
• Fourteen molded handles and textured treads provide the listed climbing layout.
• Four marine-grade 316 stainless steel D-rings provide the listed mooring points.
• EN ISO 25649 compliance and TÜV Safety Framework certification are stated.
• The 108 lbs dry weight supports handling and deployment planning.

Use and Capacity

The Catapult Trapeze is classified as a commercial free-swing overhang and high-climbing launch tower. It supports up to three concurrent users within the listed 600 lbs total payload. The required 8 ft water depth provides the listed launch-drop clearance zone around the inflated structure.

Operators should maintain 1.2 PSI across the three independent safety float chambers. The available product details do not list a pump, anchor system, mooring lines, repair kit, safety equipment, or connection hardware as included.

Materials and Construction

Duratex 0.9 mm, 1100-denier PVC forms the listed inflatable structure. Overlapping hot-air welded seams provide the listed structural seam system. Fourteen molded handles, textured treads, and four stainless steel D-rings form the listed climbing and mooring hardware.

Water, salt, sand, sunscreen residue, and debris can still collect around PVC panels, handles, treads, D-rings, seams, and valves. Rinse and inspect the product regularly. Follow manufacturer guidance for inflation, anchoring, cleaning, and storage.

Installation and Setup

The Aquaglide tower uses a 13 ft 5 in by 11 ft 2 in footprint and weighs 108 lbs when dry. Installers should select a location with at least 8 ft of water depth, allow room for the full module and launch-drop zone, and identify four mooring positions before deployment.

Inflate all three float chambers to the listed 1.2 PSI operating pressure. The provided product data does not confirm a pump, anchors, mooring lines, repair kit, safety equipment, or connection hardware as included.

Care and Operating Notes

Rinse the PVC surfaces, handles, climbing treads, D-rings, seams, and inflation valves with fresh water after use. Remove salt, sand, sunscreen residue, and debris before storage or reinflation. Inspect chambers, handles, treads, D-rings, seams, valves, and visible PVC panels before operation. Follow manufacturer instructions for inflation, repairs, cleaning products, storage, and approved replacement parts.

Warranty and Support

The Catapult Trapeze carries a 3-year limited commercial fleet protection warranty. Coverage follows the manufacturer’s stated warranty terms and may be subject to exclusions, conditions, and registration requirements.

Before Ordering

Confirm that the intended water location provides at least 8 ft of depth and room for the 13 ft 5 in by 11 ft 2 in module. Plan for no more than three users within the 600 lbs total payload, maintain 1.2 PSI across three float chambers, account for the 108 lbs dry weight, and arrange four mooring points.