FREE DELIVERY TODAY - Place your 1st order.

Until the end of the sale:
00
days
00
hours
00
minutes
00
sec.

B&G Hydraulic Ram Type 1 – 12V

Sailing yachts up to 22,000 lbs maintain steady rudder control through the B&G Hydraulic Ram Type 1 linear drive, which pushes 770 lbs of peak hydraulic thrust across a 250mm stroke in 12 seconds at 12V.

  • 770-lb thrust actuates rudder quadrants directly
  • Self-contained hydraulic ram eliminates external hose plumbing
  • 12-second stroke speed ensures responsive wave correction
  • Zero-backlash linkage preserves positive rudder feel
  • Drives cruising sailboats up to 22000 lbs
$1,555.00

Products are almost sold out

This product is about to run out

available only:

4

In Stock

Wholesale Price
Request for Quotation
Add to wishlist
Compare
SKU: BNG-RAM1-12V Category: Brand:
SKU:

BNG-RAM1-12V

Description

The B&G T1 Pilot Ram 12V, SKU RAM-T1-12V, is a self-contained hydraulic linear autopilot drive for compatible mechanically steered sailing vessels. It connects directly to an independent tiller arm or steering quadrant and integrates its hydraulic pump, reservoir, and ram in one assembly, eliminating external hydraulic hoses between the drive components. This is a drive-only component and requires a compatible B&G or Simrad autopilot course computer, display, heading sensor, power circuit, feedback method where required, and correctly engineered steering linkage.

The 12V Type 1 ram is designed for sailboats and displacement vessels up to 12,000 kg, or 26,400 lb, and provides 350 kg, or 770 lb, peak thrust through a 250 mm stroke. It draws approximately 5A to 12A depending on steering load and is intended for use with compatible NAC-2, NAC-3, AC42, or H5000 pilot systems. Confirm steering geometry, vessel displacement, course-computer output capacity, and full manual-steering operation before purchase.

Key Specifications

  • B&G Type 1 self-contained 12V hydraulic linear autopilot ram, SKU RAM-T1-12V.
  • Designed for compatible mechanically steered sailboats and displacement vessels up to 12,000 kg, or 26,400 lb.
  • Provides approximately 350 kg, or 770 lb, peak thrust.
  • Uses a 250 mm linear stroke and connects to a compatible independent tiller arm or steering quadrant.
  • Integrates the hydraulic pump, reservoir, and ram into one assembly without external hydraulic hoses between drive components.
  • Requires a compatible NAC-2, NAC-3, AC42, H5000, or other approved high-capacity autopilot course computer.
  • Operates from a 12V DC vessel electrical system and requires wiring and protection suitable for the installed steering load.
  • Includes mounting pin, clevis, and associated installation hardware.

System Integration

This is not a complete autopilot system. Add a compatible B&G or Simrad course computer, controller or display, heading sensor, electrical supply, NMEA 2000 network where applicable, and physical rudder feedback if required by the selected steering system. Do not connect the ram to a low-current autopilot computer unable to support the drive’s motor and clutch load.

Correct drive selection depends on displacement, steering load, rudder torque, tiller-arm radius, required stroke, duty cycle, and mounting geometry. The self-contained hydraulic construction simplifies the drive assembly but does not remove the need for a properly designed mechanical linkage and structural mounting foundation.

Installation Considerations

Install the ram on a rigid foundation below deck and align its pivot points with the independent tiller arm or quadrant to prevent side loading, binding, over-travel, or restricted manual steering. Confirm the full 250 mm stroke is available. Use properly sized marine wiring and circuit protection, keep cables clear of moving steering components, and complete course-computer configuration, rudder-feedback setup where fitted, and sea-trial calibration after installation.

Before Ordering

Confirm vessel displacement up to 26,400 lb, compatible mechanical steering, independent tiller arm or quadrant, sufficient 250 mm stroke clearance, structural mounting strength, compatible NAC-2, NAC-3, AC42, or H5000 course computer, 12V supply, required drive-current capacity, feedback requirement, manual-steering access, and complete autopilot-system components before purchase.

B&G Hydraulic Ram Type 1 - 12V

Drive TypeHeavy-Duty Hydraulic Linear Drive
Pump/Ram CapacityIntegrated Reversible Hydraulic Pump
Flow Rate / Speed12 Seconds (Full Stroke Span)
Max Pressure770 lbs (350 kg) Peak Thrust
Cylinder CompatibilitySailboats up to 22,000 lbs (10,000 kg)
Operating Voltage12V DC System
Peak Current Draw15 Amps Maximum Load
Average Power Draw4A - 8A Typical Sailing Use
Motor TypePermanent Magnet Reversing DC
Computer CompatibilityNAC-2, AC42, Triton2, H5000
Port Size / ThreadSelf-Contained (No External Hoses)
Drive ConnectionTiller Arm / Quadrant Pin
Rotation/Stroke DirectionLinear Push-Pull (250mm Stroke)
Mounting TypeFixed Pivot Foot Bracket
Housing MaterialAnodized Aluminum & Stainless Steel
Waterproof RatingIPX6 Marine Protected
Operating Temperature-15°C to +60°C Extreme Grade
Length (Overall)710 mm Fully Extended
Width/Diameter120 mm Main Body Diameter
Weight7.2 kg (15.8 lbs)
Included AccessoriesMounting Pin, Clevis, Hardware Kit
Key Mechanical FeatureZero-backlash precision steering linkage

Reviews

There are no reviews yet.

Be the first to review “B&G Hydraulic Ram Type 1 – 12V”

You may also like…

Shopping Cart

No products in the cart.

Free Shipping on All Orders Over $1,000

Log in

You dont have an account yet? Register Now

Type the product you want to search for and press enter.