FREE DELIVERY TODAY - Place your 1st order.

Until the end of the sale:
00
days
00
hours
00
minutes
00
sec.

Garmin Class B Compact v2 Drive Unit

Confined steering flats on sailboats up to 28,500 lbs accommodate this Garmin Class B Compact linear drive, which delivers 1,100 lbs of hydraulic thrust across a 250mm stroke within an integrated hose-free chassis at 16.5 lbs.

  • 1100-lb peak thrust moves rudder quadrants
  • Space-saving 120mm profile fits tight flats
  • Zero external hoses prevent hydraulic leaks
  • Draws 2A to 4A sailing cruising
  • IPX6-rated housing withstands harsh bilge conditions
$1,431.00

Products are almost sold out

This product is about to run out

available only:

4

In Stock

Wholesale Price
Request for Quotation
Add to wishlist
Compare
SKU: GRM-CLB-V2-DU Category: Brand:
SKU:

GRM-CLB-V2-DU

Description

The Garmin Class B Compact v2 Drive Unit is a self-contained hydraulic linear actuator for compatible mechanically steered sailboats and displacement vessels. It connects to an independent tiller arm or steering quadrant through a pivot and clevis linkage, combining the hydraulic pump and ram in one compact assembly. This is a drive-only component and requires a compatible Garmin Reactor 40 Mechanical autopilot system, high-current ECU, control display or chartplotter, heading sensor, power circuit, and correctly engineered steering linkage.

The 12V drive provides a 250 mm linear stroke and up to 500 kg, or 1,100 lb, peak thrust. It can draw up to 15A under maximum load and is intended for vessels up to 13,000 kg, or 28,500 lb, displacement. The compact integrated design eliminates external hydraulic hoses between the pump and ram, but it still requires a rigid mounting foundation, correct steering geometry, and full manual-rudder travel.

Key Specifications

  • Self-contained 12V hydraulic linear autopilot drive for compatible mechanically steered vessels.
  • Designed for compatible sailboats and displacement vessels up to 13,000 kg, or 28,500 lb.
  • Provides a 250 mm linear push-pull stroke.
  • Delivers up to 500 kg, or 1,100 lb, peak thrust.
  • Uses an integrated reversing DC hydraulic pump with no external pump-to-ram hose requirement.
  • Draws up to 15A under maximum steering load.
  • Connects to a compatible steering quadrant or independent tiller arm through a pivot-foot and clevis linkage.
  • Weighs approximately 7.5 kg and uses anodized aluminum and stainless-steel construction for protected marine installation.

System Integration

This is not a complete autopilot system. It requires a Garmin Reactor 40 Mechanical corepack or other Garmin-approved high-current system configured for the correct drive class, plus a compatible control display or chartplotter, heading sensor, power circuit, and feedback arrangement where required. Do not connect it to a low-current autopilot computer or wheel-drive controller.

Match the drive to actual vessel displacement, rudder torque, steering-arm radius, stroke requirement, maximum drive current, and manual-steering arrangement. A physical rudder-feedback sensor may be required depending on the selected Reactor 40 configuration and vessel steering system.

Installation Considerations

Install the actuator under deck on a rigid foundation with pivot points aligned to prevent binding, side loading, over-travel, or restricted manual steering. Confirm that the entire 250 mm stroke is available before installation. Use correctly sized marine-grade wiring, suitable 15A circuit protection, secure terminals, and protected cable routing. Follow Garmin dockside configuration and sea-trial procedures after installation.

Before Ordering

Confirm vessel displacement up to 28,500 lb, compatible mechanical steering, an independent tiller arm or steering quadrant, sufficient 250 mm stroke clearance, structural mounting strength, Garmin Reactor 40 Mechanical compatibility, approved drive-class configuration, 12V supply, 15A circuit capacity, feedback requirement, manual-steering access, and complete autopilot-system components before purchase.

Garmin Class B Compact v2 Drive Unit

Drive TypeCompact Hydraulic Linear Drive
Pump/Ram CapacityIntegrated Precision Hydraulic System
Flow Rate / SpeedHard-over to Hard-over: 13 Seconds
Max Pressure1,100 lbs (500 kg) Peak Thrust
Cylinder CompatibilitySailboats up to 28,500 lbs (13,000 kg)
Operating Voltage12V DC System
Peak Current Draw15 Amps Maximum
Average Power Draw2A - 4A Typical Sailing Conditions
Motor TypeIntegrated Reversing DC Pump
Computer CompatibilityReactor 40 Mechanical Corepack
Port Size / ThreadSelf-Contained (Zero External Hoses)
Drive ConnectionTiller Arm / Quadrant Pin
Rotation/Stroke DirectionLinear Push-Pull (250mm Stroke)
Mounting TypeFixed Pivot Foot Bracket
Housing MaterialAnodized Aluminum & Stainless Steel
Waterproof RatingIPX6 Marine Protected
Operating Temperature-15°C to +60°C Extreme Performance
Length (Overall)710 mm Fully Extended
Width/Diameter120 mm Slim Profile Chassis
Weight7.5 kg (16.5 lbs)
Included AccessoriesMounting Pin, Clevis, Hardware
Key Mechanical FeatureSpace-saving design for confined steering flats

Reviews

There are no reviews yet.

Be the first to review “Garmin Class B Compact v2 Drive Unit”

You may also like…

Shopping Cart

No products in the cart.

Free Shipping on All Orders Over $1,000

Log in

You dont have an account yet? Register Now

Type the product you want to search for and press enter.