Furuno NavPilot 711C/OB Autopilot f/Outboards

Description

Configure an outboard-focused autopilot system with the Furuno NavPilot 711C/OB Autopilot for Outboards. The package combines a 711C control display, FAP-7002 processor, and sun cover for compatible single or dual outboard hydraulic-steering arrangements. It supports 1.0 L and 1.2 L pumps, uses 12V or 24V DC power, and connects through a CAN-bus and NMEA 2000 system architecture.

The 115 mm by 115 mm control head uses a flush-mount layout and has an IP56 rating, while the processor is rated IPX0 and requires protected installation. Peak motor-drive current is 20A, and the control-head idle draw is 0.15A. Fantum Feedback steering logic and Sabiki Mode are system functions that depend on compatible pump, steering, processor, sensor, and vessel installation components.

Key Specifications of the Furuno NavPilot 711C/OB Autopilot for Outboards

• The outboard autopilot package includes a 711C display, FAP-7002 processor, and sun cover for compatible steering-system installation.
• Single or dual outboard hydraulic steering rams can use compatible 1.0 L or 1.2 L pumps within the system configuration.
• A 12V or 24V DC supply supports the processor and drive system, with 20A peak current specified for motor output.
• CAN-bus and NMEA 2000 connections provide the stated network architecture between compatible autopilot components and vessel electronics.
• The flush-mount control head measures 115 mm by 115 mm and carries an IP56 rating for the documented helm display environment.
• The processor has an IPX0 rating, requiring installation in a protected location away from direct water exposure.
• Fantum Feedback and Sabiki Mode operate through the configured autopilot system with compatible steering and sensor components.

System Integration and Steering

This Furuno NavPilot package is intended for compatible outboard hydraulic-steering systems and does not replace the vessel’s steering components. A matched pump, steering ram, heading sensor, power circuit, network connection, and complete hydraulic installation are required. The FAP-7002 processor controls the system, while the 711C display provides a flush-mount control interface.

Confirm whether the vessel has one or two outboards, identify the installed hydraulic steering arrangement, and select the correct compatible pump capacity. Plan the protected processor location, display mounting space, CAN-bus and NMEA 2000 connections, 12V or 24V supply, and 20A circuit capacity before installation.

Why Choose the Furuno NavPilot 711C/OB Autopilot for Outboards

The Furuno NavPilot 711C/OB Autopilot for Outboards combines a 711C display, FAP-7002 processor, 1.0 L or 1.2 L pump compatibility, 12V or 24V support, CAN-bus networking, and 20A peak drive capacity. Its single or dual outboard hydraulic-steering compatibility, IP56 control head, protected processor requirement, 115 mm display size, Fantum Feedback, and Sabiki Mode provide defined integration details for an outboard autopilot system.

Setup and Network Considerations

Confirm that the vessel uses compatible hydraulic steering for one or two outboards before selecting this package. Choose the correct 1.0 L or 1.2 L pump, plan a protected location for the IPX0 processor, and reserve a 115 mm by 115 mm flush-mount location for the display. Verify 12V or 24V supply, 20A peak circuit capacity, CAN-bus and NMEA 2000 connections, sensor placement, and hydraulic routing before commissioning.

Warranty and Support

Furuno warranty terms vary by product and region, and the supplied specifications do not provide a named warranty period for the NavPilot 711C/OB package. Mulmarine.com can help you review single or dual outboard compatibility, pump capacity, processor placement, display mounting, hydraulic-steering requirements, power supply, network connections, and required sensor components before purchase. Review the applicable Furuno warranty coverage and documented package contents before ordering.

Before Ordering the Furuno NavPilot 711C/OB Autopilot for Outboards

Confirm that your vessel has compatible single or dual outboard hydraulic steering and requires an outboard autopilot system. You should verify the 1.0 L or 1.2 L pump selection, hydraulic ram compatibility, protected FAP-7002 processor location, 115 mm display space, 12V or 24V supply, 20A circuit capacity, CAN-bus and NMEA 2000 connections, and complete steering-system requirements before purchase.