Lewmar V700G Vertical Windlass (Dual Chain Gypsy) – For Boats Up To 35 ft. Max Pull: 700 lbs.

Description

TheLewmar V700Guses a 320W 12V DC motor in a low-profile vertical gypsy-only configuration. The windlass has a stated maximum pull of 700 lbs and a 175 lbs continuous hauling-load rating. Its cast 316 stainless steel body and drive shaft form the deck and drive assembly for 1/4 in G4 or BBB chain with 1/2 in three-strand rope.

A manual friction clutch controls the listed release system and includes a built-in anchor lock. The unit fits deck thicknesses from 0.8 to 1.6 in. The provided product data does not confirm an anchor, rode, switch, contactor, or circuit breaker as included.

Key Features of the V700G Vertical Windlass

• The 320W 12V DC motor powers low-profile vertical anchor rode retrieval.
• The gypsy accepts 1/4 in G4 or BBB chain.
• The rope section handles 1/2 in three-strand rope in the matched rode.
• The manual friction clutch controls the listed anchor rode release system.
• The built-in anchor lock forms part of the listed clutch system.
• The 175 lbs working-load rating identifies the continuous hauling load.
• The 700 lbs maximum pull figure states the product’s peak pull rating.
• The rated no-load speed reaches 82 ft/min without a working load.
• The windlass reaches 49 ft/min at its stated working-load rating.
• A 35A circuit breaker is required for electrical circuit protection.

Which Boats This Windlass Fits

The V700G vertical windlass is recommended for power and sailboats up to 35 ft. Its gypsy requires 1/4 in G4 or BBB chain paired with 1/2 in three-strand rope. The chain grade, chain size, and rope diameter must match the confirmed gypsy configuration before selecting anchor rode components.

the listed maximum pull is 700 lbs. The 175 lbs working-load rating identifies the separate continuous hauling value. Boat owners should evaluate regular retrieval needs against the continuous rating rather than the listed peak pull figure.

Materials, Technology and Use

Cast 316 stainless steel forms the body and drive shaft of the deck-mounted unit. the listed IP67 marine deck-protection rating applies to the deck installation. The manual friction clutch manages the listed release system, and the built-in anchor lock forms part of the listed configuration.

Salt residue and debris can still collect around stainless steel hardware, the gypsy, and the anchor rode. Regular cleaning and inspection remain necessary. The gypsy-only configuration handles the compatible rope-to-chain rode without a separate warping drum.

Compatibility and Installation

The Lewmar vertical windlass fits decks from 0.8 to 1.6 in thick. The unit measures 85 mm above deck with a 125 mm base diameter and weighs 14.3 lbs. Installers should verify below-deck space, cable routing, mounting area, and clutch access before cutting or drilling the deck.

The 12V DC circuit draws an average of 30A and requires a 35A circuit breaker. Installers can review onboard charging layout while planning around the listed electrical requirements. The provided product data does not confirm a switch, contactor, or circuit breaker as included.

Care and Operating Notes

Rinse the exposed housing, gypsy, chain, and rope with fresh water after saltwater exposure. Remove salt, sand, mud, and debris from the rope-to-chain transition and manual clutch area before operation. Inspect chain links, rope condition, anchor lock operation, visible fasteners, and electrical connections before departure. Follow the manufacturer manual for lubricant selection, service intervals, disassembly, and approved replacement parts.

Warranty and Support

The V700G carries a 3-year limited manufacturer warranty. The provided warranty term does not define coverage for labor, corrosion, electrical accessories, shipping, or other components. These terms reflect manufacturer-stated coverage, and buyers should verify active warranty policies directly with the seller or manufacturer prior to purchase.

Before Ordering

Confirm that your anchor rode uses 1/4 in G4 or BBB chain with 1/2 in three-strand rope. You should compare your boat with the up-to-35-ft application guide, measure deck thickness against the 0.8 to 1.6 in range, and reserve room for the 85 mm above-deck height and 125 mm base diameter. Verify that your 12V system supports the listed 30A average draw and required 35A circuit breaker. Confirm controls, circuit-protection hardware, anchor, chain, and rope with the seller because the provided product data does not confirm them as included.