Lewmar CPX2 12V Gypsy Only – 5/16″ G4 Chain 9/16″ Line

Description

Low-profile vertical mounting and a controlled free-fall clutch distinguish theLewmar CPX2gypsy-only windlass. Its 700W 12V DC motor has a stated maximum pull of 1,433 lbs and a 360 lbs continuous working-load rating. The precision-cast 316 stainless steel housing and high-tensile drive shaft form the deck and drive assembly for a 5/16 in G4 chain and 9/16 in rope system.

The Fast-Fit cone clutch provides the listed controlled free-fall function, while the manual override provides a separate control option. The gypsy accepts 9/16 in three-strand or 8-plait rope with the specified chain. The provided product data does not confirm an anchor, rode, switch, contactor, or circuit breaker as included.

Key Features of the CPX2 Vertical Windlass

• The 700W 12V DC motor powers vertical rope-to-chain rode retrieval.
• The gypsy accepts 5/16 in G4 chain for confirmed chain compatibility.
• The rope section handles 9/16 in three-strand or 8-plait rope.
• The Fast-Fit cone clutch controls the listed free-fall release function.
• The manual override provides a separate stated manual-control feature.
• The 360 lbs working-load rating identifies the continuous hauling load.
• The 1,433 lbs maximum pull figure states the peak pull rating.
• The rated no-load speed reaches 69 ft/min without a working load.
• The windlass reaches 46 ft/min at its stated working-load rating.
• A 90A slow-blow breaker is required for electrical circuit protection.

Which Boats This Windlass Fits

The CPX2 vertical windlass is recommended for sail and power vessels from 32 to 42 ft. Its gypsy requires 5/16 in G4 chain paired with 9/16 in three-strand or 8-plait rope. Both dimensions must match the confirmed rope-to-chain configuration because the gypsy handles the connected chain and rope sections during retrieval.

the listed maximum pull is 1,433 lbs, while the listed continuous working load is 360 lbs. The maximum figure describes peak pull capacity. The working-load figure provides the separate reference for sustained hauling assessment.

Materials, Technology and Use

Precision-cast 316 stainless steel forms the exposed housing, and the high-tensile shaft supports the drive assembly. the listed IP67 rating applies to the motor and gearbox. The controlled free-fall cone clutch manages the listed release function, while the manual override provides a separate manual-control feature.

Salt deposits and debris can still remain around stainless steel hardware, the gypsy, and surrounding deck surfaces. Regular cleaning and inspection remain necessary. The gypsy-only configuration manages the correctly matched anchor rode and does not include a capstan drum.

Compatibility and Installation

The Lewmar vertical windlass fits deck thicknesses from 1.0 to 2.0 in. The deck unit measures 110 mm high with a 161 mm base diameter and weighs 29.7 lbs. Installers should verify room below deck for the motor and gearbox, then plan cable routing and clutch access before beginning the installation.

The 12V DC system draws an average of 80A and requires a 90A slow-blow breaker. the listed electrical requirements should be assessed with marine charging considerations before selecting the installation layout. The provided product data does not confirm a contactor, switch, or circuit breaker as included.

Care and Operating Notes

Rinse the exposed housing, gypsy, chain, and rope with fresh water after saltwater exposure. Clear salt, sand, mud, and debris from the rope-to-chain transition and clutch area before operation. Inspect chain links, rope condition, the three-strand or 8-plait rope section, manual override access, visible fasteners, and electrical connections before departure. Follow the manufacturer manual for lubricant selection, service intervals, disassembly, and approved replacement parts.

Warranty and Support

The CPX2 carries a 3-year limited manufacturer warranty. The provided warranty term does not define coverage for labor, corrosion, electrical accessories, shipping, or other components. These terms reflect manufacturer-stated coverage, and buyers should verify active warranty policies directly with the seller or manufacturer prior to purchase.

Before Ordering

Confirm that your anchor rode combines 5/16 in G4 chain with 9/16 in three-strand or 8-plait rope. You should compare your vessel with the 32 to 42 ft application guide, measure deck thickness against the 1.0 to 2.0 in range, and reserve space for the 110 mm-high deck unit and below-deck motor assembly. Verify that your 12V system supports the listed 80A average draw and required 90A slow-blow breaker. Confirm controls, circuit protection hardware, anchor, chain, and rope with the seller because the provided product data does not confirm them as included.