Lewmar CPX3 12v Gypsy Only – 3/8″ Chain 5/8″ Line

Description

TheLewmar CPX3uses a 1,000W 12V DC motor in a low-profile, vertical gypsy-only configuration for rope-to-chain anchor rode handling. The windlass has a stated maximum pull of 1,808 lbs and a 452 lbs continuous working-load rating. Its cast 316 stainless steel housing and high-tensile alloy shaft form the deck and drive assembly.

The gypsy accepts 3/8 in G4 chain with 5/8 in three-strand or 8-plait rope. A controlled free-fall cone clutch manages the listed release system, while the emergency manual override provides a separate control function. The provided product data does not confirm an anchor, rode, switch, contactor, or circuit breaker as included.

Key Features of the CPX3 Vertical Windlass

• The 1,000W 12V DC motor powers vertical rope-to-chain rode retrieval.
• The gypsy accepts 3/8 in G4 chain for confirmed anchor rode compatibility.
• The rope section handles 5/8 in three-strand or 8-plait rope.
• The cone clutch controls the listed free-fall rode release function.
• The emergency manual override provides a separate stated control feature.
• The 452 lbs working-load rating identifies the continuous hauling load.
• The 1,808 lbs maximum pull figure states the peak pull rating.
• The rated no-load speed reaches 69 ft/min without a working load.
• The windlass reaches 52 ft/min at its stated working-load rating.
• A 110A circuit breaker is required for electrical circuit protection.

Which Boats This Windlass Fits

The CPX3 vertical windlass is recommended for cruisers and yachts from 38 to 50 ft. Its gypsy requires 3/8 in G4 chain paired with 5/8 in three-strand or 8-plait rope. Both dimensions must match the confirmed configuration because the gypsy manages the connected chain and rope sections during anchor retrieval.

The 1,808 lbs figure represents the listed maximum pull rating. The 452 lbs working-load rating provides the separate continuous hauling value. Buyers should use the continuous rating when assessing regular retrieval loads.

Materials, Technology and Use

Cast 316 stainless steel forms the exposed deck housing, while the high-tensile alloy shaft supports the drive assembly. the listed IP67 rating applies to the motor and gearbox. The controlled free-fall cone clutch manages the listed release function, and the emergency manual override provides a separate stated control option.

Salt deposits and debris can still collect around stainless steel hardware, the gypsy, and the surrounding deck area. Regular cleaning and inspection remain appropriate. The gypsy-only configuration manages the matched anchor rode and does not include a warping drum.

Compatibility and Installation

The Lewmar vertical windlass fits deck thicknesses from 1.0 to 2.0 in. The deck unit measures 110 mm high with a 182 mm base diameter and weighs 40.8 lbs. Installers should verify space below deck for the motor and gearbox, then confirm cable routing and access to the clutch before cutting the mounting location.

The 12V DC system draws an average of 100A and requires a 110A circuit breaker. Electrical planning should include windlass charging requirements alongside the listed breaker and current-draw figures. The provided product data does not confirm a switch, contactor, or circuit breaker as included.

Care and Operating Notes

Rinse the exposed housing, gypsy, chain, and rope with fresh water after saltwater exposure. Remove salt, sand, mud, and debris from the rope-to-chain transition and clutch area before operation. Inspect chain links, rope condition, free-fall clutch movement, emergency manual override access, visible fasteners, and electrical connections before departure. Follow the manufacturer manual for lubricant selection, service intervals, disassembly, and approved replacement parts.

Warranty and Support

The CPX3 carries a 3-year limited manufacturer warranty. The provided warranty term does not define coverage for labor, corrosion, electrical accessories, shipping, or other components. These terms reflect manufacturer-stated coverage, and buyers should verify active warranty policies directly with the seller or manufacturer prior to purchase.

Before Ordering

Confirm that your anchor rode combines 3/8 in G4 chain with 5/8 in three-strand or 8-plait rope. You should compare your boat with the 38 to 50 ft application guide, measure deck thickness against the 1.0 to 2.0 in range, and reserve room for the 110 mm-high deck unit and below-deck motor assembly. Verify that your 12V system supports the listed 100A average draw and required 110A circuit breaker. Confirm controls, circuit protection hardware, anchor, chain, and rope with the seller because the provided product data does not confirm them as included.