Lewmar CPX1 Vertical Windlass 12v Gypsy Only – 1/4″ G40 Chain 1/2″ Line

Description

TheLewmar CPX1combines a 500W continuous-duty 12V DC motor with a low-profile vertical gypsy-only arrangement. The windlass has a stated maximum pull of 1,000 lbs and a 250 lbs continuous working-load rating. Its precision-cast 316 stainless steel housing and high-tensile shaft support the drive system for 1/4 in G40 chain and 1/2 in rope.

The gypsy accepts 1/2 in three-strand or 8-plait rope with the listed 1/4 in G40 chain. A controlled free-fall cone clutch provides the listed release function, and the manual override provides a separate manual-control option. The provided product data does not confirm an anchor, rode, switch, contactor, or circuit breaker as included.

Key Features of the CPX1 Vertical Windlass

• The 500W continuous-duty motor powers vertical anchor rode retrieval on 12V DC.
• The gypsy accepts 1/4 in G40 chain for confirmed chain compatibility.
• The rope section handles 1/2 in three-strand or 8-plait rope.
• The controlled cone clutch provides the listed free-fall release function.
• The manual override provides a separate stated manual-control feature.
• The 250 lbs working-load rating defines the continuous hauling load.
• The 1,000 lbs maximum pull figure states the peak pull rating.
• The rated no-load speed reaches 62 ft/min without a working load.
• The windlass reaches 46 ft/min at its stated working-load rating.
• A 50A circuit breaker is required for electrical circuit protection.

Which Boats This Windlass Fits

The CPX1 vertical windlass is recommended for boats from 25 to 35 ft. Its gypsy requires 1/4 in G40 chain with 1/2 in three-strand or 8-plait rope. Both the chain and rope must match the confirmed dimensions because the gypsy handles the connected sections of the anchor rode.

the listed maximum pull is 1,000 lbs, while the 250 lbs working-load rating identifies the continuous hauling value. The two ratings do not describe the same operating condition. The continuous figure provides the relevant reference for regular retrieval assessment.

Materials, Technology and Use

Precision-cast 316 stainless steel forms the exposed deck housing, and the high-tensile shaft supports the drive assembly. The IP67 rating applies to the listed motor and gearbox. The controlled free-fall cone clutch manages the listed release function, while the manual override provides a separate manual-control option.

Salt deposits and debris can still collect around the stainless steel housing, gypsy, and deck hardware. Regular cleaning and visual inspection remain appropriate. The gypsy-only configuration manages the matched anchor rode and does not include a warping drum.

Compatibility and Installation

The Lewmar vertical windlass fits deck thicknesses from 0.8 to 1.6 in. The deck unit measures 90 mm high with a 145 mm base diameter and weighs 25.3 lbs. Installers should verify below-deck motor space, cable routing, and access to the clutch before cutting the mounting location.

The 12V DC system draws an average of 35A and requires a 50A circuit breaker. Planning around the listed electrical load can include battery-system coordination before completing the installation. The provided product data does not confirm a switch, contactor, or circuit breaker as included.

Care and Operating Notes

Rinse the exposed housing, gypsy, chain, and rope with fresh water after saltwater exposure. Remove salt, sand, mud, and debris from the rope-to-chain transition and cone clutch area before operation. Inspect chain links, rope condition, manual override access, visible fasteners, and electrical connections before departure. Follow the manufacturer manual for lubricant selection, service intervals, disassembly, and approved replacement parts.

Warranty and Support

The CPX1 carries a 3-year limited manufacturer warranty. The provided warranty term does not define coverage for labor, corrosion, electrical accessories, shipping, or other components. These terms reflect manufacturer-stated coverage, and buyers should verify active warranty policies directly with the seller or manufacturer prior to purchase.

Before Ordering

Confirm that your anchor rode combines 1/4 in G40 chain with 1/2 in three-strand or 8-plait rope. You should compare your boat with the 25 to 35 ft application guide, measure deck thickness against the 0.8 to 1.6 in range, and reserve space for the 90 mm-high deck unit and below-deck drive assembly. Verify that your 12V electrical system supports the listed 35A average draw and required 50A circuit breaker. Confirm controls, circuit protection hardware, anchor, chain, and rope with the seller because the provided product data does not confirm them as included.